Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Kiến trúc - Xây dựng
Aluminium Design and Construction - Chapter 10
Đang chuẩn bị liên kết để tải về tài liệu:
Aluminium Design and Construction - Chapter 10
Huy Anh
88
27
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tài liệu tham khảo giáo trình nhôm trong thiết kế xây dựng bằng tiếng anh - Chương 10 Calculation of section properties 10.1 SUMMARY OF SECTION PROPERTIES USED The formulae in Chapters 8 and 9 involve the use of certain geometric properties of the cross-section. In steel design these are easy to find, since the sections used are normally in the form of standard rollings with quoted properties. In aluminium, the position is different because of the use of non-standard extruded profiles, often of complex shape | CHAPTER 10 Calculation of section properties 10.1 SUMMARY OF SECTION PROPERTIES USED The formulae in Chapters 8 and 9 involve the use of certain geometric properties of the cross-section. In steel design these are easy to find since the sections used are normally in the form of standard rollings with quoted properties. In aluminium the position is different because of the use of non-standard extruded profiles often of complex shape. A further problem is the need to know torsional properties when considering lateral-torsional LT and torsional buckling. The following quantities arise a Flexural S Plastic section modulus I Second moment of area inertia Z Elastic section modulus r Radius of gyration. b Torsional 3 St Venant torsion factor Ip Polar second moment of area polar inertia H Warping factor px Special LT buckling factor. The phrase second moment of area gives a precise definition of I and Ip. However for the sake of brevity we refer to these as inertia and polar inertia . 10.2 PLASTIC SECTION MODULUS 10.2.1 Symmetrical bending The plastic modulus S relates to moment resistance based on a plastic pattern of stress with assumed rectangular stress blocks. It is relevant to fully compact sections equation 8.1 . Firstly we consider sections on which the moment M acts about an axis of symmetry ss Figure 10.1 a which will in this case also be the neutral Copyright 1999 by Taylor Francis Group. All Rights Reserved. Figure 10.1 Symmetric plastic bending. axis. The half of the section above ss is divided into convenient elements and S then calculated from the expression S 2 AEyE 10.1 where AE area of element and yE distance of element s centroid E above ss. The summation is made for the elements lying above ss only i.e. just for the compression material C . Figure 10.1 b shows another case of symmetrical bending in which M acts about an axis perpendicular to the axis of symmetry. The neutral axis xx will now be the equal-area axis not necessarily going through the .
TÀI LIỆU LIÊN QUAN
Aluminium Design and Construction - Chapter 1
Aluminium Design and Construction - Chapter 2
Aluminium Design and Construction - Chapter 3
Aluminium Design and Construction - Chapter 4
Aluminium Design and Construction - Chapter 5
Aluminium Design and Construction - Chapter 6
Aluminium Design and Construction - Chapter 7
Aluminium Design and Construction - Chapter 8
Aluminium Design and Construction - Chapter 9
Aluminium Design and Construction - Chapter 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.