Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Estimation of uncertainty in three dimensional coordinate measurement by comparison with calibrated points
Đang chuẩn bị liên kết để tải về tài liệu:
Estimation of uncertainty in three dimensional coordinate measurement by comparison with calibrated points
Phước Thiện
67
30
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tính không chắc chắn để đo lường là một nỗ lực để thiết lập giới hạn hợp lý cho kết quả đo lường theo quy tắc tiêu chuẩn hóa. Kể từ khi đo lường hàng sản xuất chỉ là một ước tính của câu trả lời, điều kiện tiên quyết đầu tiên của một tuyên bố không chắc chắn là để thông báo cho người đọc chắc chắn rằng nhà văn như thế nào là câu trả lời là trong một phạm vi nhất định | Volume 102 Number 6 November-December 1997 Journal of Research of the National Institute of Standards and Technology J. Res. Natl. Inst. Stand. Technol. 102 647 1997 Uncertainty and Dimensional Calibrations Volume 102 Number 6 November-December 1997 Ted Doiron and John Stoup National Institute of Standards and Technology Gaithersburg MD 20899-0001 The calculation of uncertainty for a measurement is an effort to set reasonable bounds for the measurement result according to standardized rules. Since every measurement produces only an estimate of the answer the primary requisite of an uncertainty statement is to inform the reader of how sure the writer is that the answer is in a certain range. This report explains how we have implemented these rules for dimensional calibrations of nine different types of gages gage blocks gage wires ring gages gage balls roundness standards optical flats indexing tables angle blocks and sieves. Key words angle standards calibration dimensional metrology gage blocks gages optical flats uncertainty uncertainty budget. Accepted August 18 1997 1. Introduction The calculation of uncertainty for a measurement is an effort to set reasonable bounds for the measurement result according to standardized rules. Since every measurement produces only an estimate of the answer the primary requisite of an uncertainty statement is to inform the reader of how sure the writer is that the answer is in a certain range. Perhaps the best uncertainty statement ever written was the following from Dr. C. H. Meyers reporting on his measurements of the heat capacity of ammonia We think our reported value is good to 1 part in 10 000 we are willing to bet our own money at even odds that it is correct to 2 parts in 10 000. Furthermore if by any chance our value is shown to be in error by more than 1 part in 1000 we are prepared to eat the apparatus and drink the ammonia. Unfortunately the statement did not get past the NBS Editorial Board and is only preserved .
TÀI LIỆU LIÊN QUAN
Bài giảng Chapter 4: Estimation by instrumental variables
The anomaly detection efficiency of kernel density estimation functions on UAV images
An algorithm combining synchronization and channel estimation for OFDM systems
Part one: Fabric estimation for pattern cutting
Lecture Cost management: A strategic emphasis (6/e) - Chapter 8: Cost estimation
Lecture Cost management: A strategic emphasis - Chapter 8: Cost estimation
Short term solarphotovoltaic power forecasting error distribution estimation
An efficient 1-D tree architecture of H.264/AVC variable block size motion estimation
Albedo estimation from PolDER data
Annotation of function point model over size estimation
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.