Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Current Trends and Challenges in RFID Part 6
Đang chuẩn bị liên kết để tải về tài liệu:
Current Trends and Challenges in RFID Part 6
Quốc Mạnh
48
30
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'current trends and challenges in rfid part 6', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 140 Current Trends and Challenges in RFID circuit to maximize the transfer of power into and out of it. We selected an Alien s Gen 2 RFID chip which has an impedance value of 30 - 110j Q so we designed the tag antenna with the impedance value of 30 110j Q to conjugate match with the chip. In the simulation we considered both the resistivity of the materials surface roughness and configuration of the antenna. Based on the simulation result we designed a series of RFID tag antenna based on 1 and 2 series. The antenna is a 82 mm-long dipole with a short line connecting two parts as shown in Fig. 9. 36 For example the simulated impedance of the ECA antenna filled with 30 wt of silver filler is 33 108j at 915 MHz which well matches the Alien s RFID strap 30 - 110j . The calculated return loss values is -24 dB which means over 99 power is transmitted to RFID chip. We found that the -10 dB power transmission bandwidth of the antenna is 60 MHz which covers the operation frequency of North American China and Hong Kong standards. 37 Herein we use the minimum turn-on power of the reader as the index of the RFID tag antenna performance. The reader is located one meter in distance towards the RFID tag a piece of EPCglobal Class 1 Gen 2 RFID Chip is adhered to the center of the antenna . From the experimental result we can observe that the minimum turn-on power of the reader is consistent with the electrical resistivity of the ECA samples i.e. with the increment of the resistivity of the antenna the reader needs a higher minimum turn-on power to detect the tag Fig. 12 . Therefore using the same antenna design we can adjust the content of silver filler in the ECA to cater to different requirement of read range. As for the real application of RFID technique the power out-put of the reader is often fixed to a certain value. Controlling the resistivity of the ECA can probably be a convenient way to cater to the different requirement of read range requirement. Apparently that by .
TÀI LIỆU LIÊN QUAN
Current Trends and Challenges in RFID Part 18
Current Trends and Challenges in RFID Part 1
Current Trends and Challenges in RFID Part 2
Current Trends and Challenges in RFID Part 3
Current Trends and Challenges in RFID Part 4
Current Trends and Challenges in RFID Part 5
Current Trends and Challenges in RFID Part 6
Current Trends and Challenges in RFID Part 7
Current Trends and Challenges in RFID Part 8
Current Trends and Challenges in RFID Part 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.