Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
An Experimental Investigation of Machinability of Inconel 718 in Electrical Discharge Machining
Đang chuẩn bị liên kết để tải về tài liệu:
An Experimental Investigation of Machinability of Inconel 718 in Electrical Discharge Machining
Trúc Vân
102
7
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
(BQ)This paper proposes an experimental investigation and optimization of the various machining parameters for the electrical discharge machining (EDM) processes on Inconel 718 super alloy using a multi objective particle swarm optimization (MOPSO) algorithm. | Available online at www.sciencedirect.com ScienceDirect Procedia Materials Science 6 (2014) 605 – 611 3rd International Conference on Materials Processing and Characterisation (ICMPC 2014) An Experimental Investigation of Machinability of Inconel 718 in Electrical Discharge Machining Chinmaya P Mohanty*, Siba Shankar Mahapatra, Manas Ranjan Singh Departement of mechanical Engineering, National Institute of Technology,Rourkela,Odisha,India,769008 Abstract This paper proposes an experimental investigation and optimization of the various machining parameters for the electrical discharge machining (EDM) processes on Inconel 718 super alloy using a multi objective particle swarm optimization (MOPSO) algorithm. A Box-Behnkin design of response surface methodology has been used to collect data for the study. The machining performances of the process are evaluated in terms of material removal rate (MRR) and surface quality which are functions of process variables such as open circuit voltage, discharge current, pulse-on-time, duty factor, flushing pressure and tool material. Mathematical model is developed relating responses with process variables. Finally, a MOPSO algorithm has been proposed for the multi objective optimization of the responses. © 2014 The Authors. Published by Elsevier Ltd. © 2014 Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/). the Gokaraju Rangaraju Institute of Engineering and Technology (GRIET). Selection and peer-review under responsibility of Selection and peer review under responsibility of the Gokaraju Rangaraju Institute of Engineering and Technology (GRIET) Keywords: Electrical Discharge Machining;Inconel 718;Response Surface Methodology;Multi Objective Particle SwarmOptimization ; 1. Introduction The non-conventional machining processes are more capable than conventional machining process owing to ease of machining of hard materials with complex shapes in the .
TÀI LIỆU LIÊN QUAN
An experimental investigation and statistical modelling for trim cutting operation in WEDM of Nimonic-90
Experimental investigation on hard turning using mixed ceramic insert under accelerated cooling environment
Experimental investigation on the effect of pre-treatments on thin layer drying and quality characteristics of green mangoes in forced convection hot air drying
Experimental and numerical investigation on the tensile and water absorption behavior of jute carbon reinforced epoxy composite
Experimental investigation on improving the cooling performance of automobile radiator by using cuo nanofluid
Experimental investigation of various process parameters of powder mixed electro discharge machining process for machining of Al- si alloy
Experimental investigation of coated and uncoated tools used in electro discharge machining process for machining of TI6AL4V
Experimental investigation of double slope stepped solar still
Experimental investigation of impact and hardness properties of hybrid laminated plates
Experimental investigation of mechanical hydrostatic continuously variable transmission
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.