Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Know and Understand Centrifugal Pumps Episode 10
Đang chuẩn bị liên kết để tải về tài liệu:
Know and Understand Centrifugal Pumps Episode 10
Ngọc Ái
57
20
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'know and understand centrifugal pumps episode 10', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Know and Understand Centrifugal Pumps To remove old grease from the bearing internals and the housing Remove as much as possible by hand. Flush the bearing and housing with warm kerosene. Following by a flush with mineral oil SAE 10 viscosity. If the old grease is caked and hardened Soak the bearing and housing in heated kerosene. Slowly rotate the bearing by hand. Rinse the bearing with clean kerosene or degreasing solvent. Again rotate the bearing s outer race by hand while applying a modest axial and radial load to the balls and races. Soak and rinse again as necessary until the bearing rotates freely and smoothly. Once all the old grease is removed from the housing and the bearing is cleaned it should be thoroughly inspected for damage. If the bearing is not damaged it can be repacked with new grease of the correct type and consistency and reinstalled in the equipment or stored for future use. To store the bearing wrap it completely in wax or oilpaper and place into a storage box. The following table contains some simple Do s and Don ts for handling and working with bearings. Memorizing and practicing these suggestions will extend the service life of rolling element bearings. Do s Don ts 1. Make sure all tools and surroundings are clean. 2. Use only clean lint-free cloths with no strings to wipe bearings. 3. Use only clean flushing fluids and solvents. 4. Don t handle bearings by hand. It s best to use clean cotton gloves. 5. Remove all outside dirt from the housing before exposing the bearings. 6. Make sure the internal bearing chamber is clean before replacing bearings. Don t use chipped or dirty tools. Don t use cotton waste or dirty cloths to wipe bearings. Don t use leaded gasoline to rinse bearings. The chemical additives are harmful to your health. Don t handle bearings with wet or dirty hands. Don t work in a dirty surrounding. Don t scratch or nick any bearing housing or shaft contact surface. 164 Bearings Do s Don ts 7. Place bearings on clean paper.
TÀI LIỆU LIÊN QUAN
Mr. Know-All by William Somerset Maugham
Ebook 1100 words you need to know
Phân biệt cách sử dụng: To Know, To Know How.
Ebook Sir i know it
Ebook I know alike and different
Ebook Math concept reader: I Know Shapes
How Documents Know Their Parents
The least you should know about English
GETTING TO KNOW THE TOEFL
The Essential TOEFL Vocabulary
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.