Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Kinematic Geometry of Surface Machinin Episode Episode 12
Đang chuẩn bị liên kết để tải về tài liệu:
Kinematic Geometry of Surface Machinin Episode Episode 12
Khải Tâm
92
30
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'kinematic geometry of surface machinin episode episode 12', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 8__ Accuracy of Surface Generation Accuracy of the machined part surfaces is a critical issue for many reasons. Deviations of the actual part surface from the desired part surface are investigated in this chapter from the prospective of capabilities of the theory of surface generation. Two major reasons often cause surface deviation When machining a part surface the entire generating surface of the cutting tool does not actually exist. In all cases of implementation of wedge cutting tools the generating surface of the cutting tool is not represented entirely but by a limited number of cutting edges. In other words the generating surface of the cutting tool is represented discretely. The discrete representation of the surface T of the cutting tool causes deviations of the actual machined part surface Pac from the desired say from the nominal part surface Pnom. Point contact of the part surface and of the generating surface of the cutting tool is usually observed when machining a sculptured surface on a multi-axis numerical control NC machine. When the surfaces make point contact then articulation capabilities of the multi-axis NC machine can be utilized in full. From this prospective point contact of the surfaces can be considered as the most general kind of surface contact. However point contact of the surfaces P and T also causes deviations of the actual machined part surface Pac from the desired part surface Pnom . Ultimately when the generating surface T of a cutting tool is represented discretely and the surfaces P and T make point contact then the deviations of the actual machined part surface Pac from the desired part surface Pnom are getting bigger. Sources for the deviations of the machined part surface from the desired part surface are limited to two major reasons only in a simplified case of surface machining. In the simplified cases of surface machining no deviations in the surfaces P and T configuration are observed.
TÀI LIỆU LIÊN QUAN
Kinematic Geometry of Surface Machinin Episode Episode 6
Kinematic Geometry of Surface Machinin Episode Episode 7
Kinematic Geometry of Surface Machinin Episode Episode 8
Kinematic Geometry of Surface Machinin Episode Episode 9
Kinematic Geometry of Surface Machinin Episode Episode 10
Kinematic Geometry of Surface Machinin Episode Episode 11
Kinematic Geometry of Surface Machinin Episode Episode 12
Kinematic Geometry of Surface Machinin Episode Episode 13
Kinematic Geometry of Surface Machinin Episode Episode 14
Kinematic Geometry of Surface Machinin Episode Episode 15
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.