Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Kinematic Geometry of Surface Machinin Episode Episode 11
Đang chuẩn bị liên kết để tải về tài liệu:
Kinematic Geometry of Surface Machinin Episode Episode 11
Diệu Huyền
28
30
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'kinematic geometry of surface machinin episode episode 11', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Conditions of Proper Part Surface Generation 329 FIGURE 7.26 Cusps on the machined sculptured part surface P. From Radzevich S.P. Computer-Aided Design 34 10 727-740 2002. With permission. can be generated. The form transition surface is machined instead. This is due to violation of the fifth necessary condition of proper PSG. 7.2.6 The Sixth Condition of Proper Part Surface Generation When machining a sculptured surface point contact of the surfaces P and T is usually observed. Due to point contact of the surfaces the discrete generation of the sculptured surface often occurs. Representation of the generating surface T by distinct cutting edges of the form-cutting tool is the other reason the discrete generation of the sculptured surface takes place. In an instant of time it is physically impossible to generate the sculptured surface P by a single moving point. When the discrete surface generation occurs the nominal smooth regular sculptured surface P n and the actual machined surface P a are not identical. The actual part surface P a can be interpreted as the nominal sculptured surface P n that is covered by cusps Figure 7.26 or may have other deviations from P n . The sixth necessary condition of proper PSG is formulated as follows The Sixth Condition of Proper PSG The actual part surface P with cusps if any must remain within the tolerance on surface accuracy. Cusps on the machined sculptured surface P must be within the tolerance on the surface accuracy. Then maximal height hỵ of the cusps must not exceed the tolerance h on the sculptured surface accuracy. Consider a Cartesian coordinate system XPYPZP associated with the sculptured surface P. The sixth necessary condition of proper PSG is satisfied if and only if the following condition is satisfied at every point of the nominal sculptured surface P n n h r a - r n r t n n hl 7.40 nP ỵ rP rP rP nP . 2008 by Taylor Francis Group LLC 330 Kinematic Geometry of Surface Machining where the position vector of a .
TÀI LIỆU LIÊN QUAN
Kinematic Geometry of Surface Machinin Episode Episode 6
Kinematic Geometry of Surface Machinin Episode Episode 7
Kinematic Geometry of Surface Machinin Episode Episode 8
Kinematic Geometry of Surface Machinin Episode Episode 9
Kinematic Geometry of Surface Machinin Episode Episode 10
Kinematic Geometry of Surface Machinin Episode Episode 11
Kinematic Geometry of Surface Machinin Episode Episode 12
Kinematic Geometry of Surface Machinin Episode Episode 13
Kinematic Geometry of Surface Machinin Episode Episode 14
Kinematic Geometry of Surface Machinin Episode Episode 15
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.