Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Plastics Materials 7 Episode 3
Đang chuẩn bị liên kết để tải về tài liệu:
Plastics Materials 7 Episode 3
Bảo Tiên
43
60
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'plastics materials 7 episode 3', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Polymer Solubility 87 3 Some materials such as water alcohols carboxylic acids and primary and secondary amines may be able to act simultaneously as proton donors and acceptors. Cellulose and poly vinyl alcohol are two polymers which also function in this way. 4 A number of solvents such as the hydrocarbons carbon disulphide and carbon tetrachloride are quite incapable of forming hydrogen bonds. Vulcanised rubber and thermosetting plastics The conventionally covalently cross-linked rubbers and plastics cannot dissolve without chemical change. They will however swell in solvents of similar solubility parameter the degree of swelling decreasing with increase in cross-link density. The solution properties of the thermoelastomers which are two-phase materials are much more complex depending on whether or not the rubber phase and the resin domains are dissolved by the solvent. 5.3.1 Plasticisers It has been found that the addition of certain liquids and in rare instances solids to a polymer will give a non-tacky product with a lower processing temperature and which is softer and more flexible than the polymer alone. As an example the addition of 70 parts of di-iso-octyl phthalate to 100 parts of PVC will convert the polymer from a hard rigid solid at room temperature to a rubber-like material. Such liquids which are referred to as plasticisers are simply high boiling solvents for the polymer. Because it is important that such plasticisers should be non-volatile they have a molecular weight of at least 300. Hence because of their size they dissolve into the polymer only at a very slow rate at room temperature. For this reason they are blended fluxed gelled with the polymer at elevated temperatures or in the presence of volatile solvents the latter being removed at some subsequent stage of the operation . For a material to act as a plasticiser it must conform to the following requirements 1 It should have a molecular weight of at least 300. 2 It should have a similar .
TÀI LIỆU LIÊN QUAN
Plastics Materials 7 Episode 7
Plastics Materials 7 Episode 3
Plastics Materials 7 Episode 4
Plastics Materials 7 Episode 5
Plastics Materials 7 Episode 6
Plastics Materials 7 Episode 8
Plastics Materials 7 Episode 9
Plastics Materials 7 Episode 10
Plastics Materials 7 Episode 11
Plastics Materials 7 Episode 12
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.