Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 9
Đang chuẩn bị liên kết để tải về tài liệu:
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 9
Xuân Bình
82
8
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'material science_ vol 1 of 2 - us doe (1993) ww part 9', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Properties of Metals DOE-HDBK-1017 1-93 YOUNG S MODULUS We can now see that Young s Modulus may be easily calculated provided that the stress and corresponding unit elongation or strain have been determined by a tensile test as described previously. Strain e is a number representing a ratio of two lengths therefore we can conclude that the Young s Modulus is measured in the same units as stress ơ that is in pounds per square inch. Table 1 gives average values of the Modulus E for several metals used in DOE facilities construction. Yield strength and ultimate strength will be discussed in more detail in the next chapter. TABLE 1 Properties of Common structural Materials E psi Yield Strength psi Ultimate Strength psi Aluminum 1.0 x 107 3.5 x 104 to 4.5 x 104 5.4 x 104 to 6.5 x 104 Stainless Steel 2.9 x 107 4.0 x 104 to 5.0 x 104 7.8 x 104 to 10 x 104 Carbon Steel 3.0 x 107 3.0 x 104 to 4.0 x 104 5.5 x 104 to 6.5 x 104 Example What is the elongation of 200 in. of aluminum wire with a 0.01 square in. area if it supports a weight of 100 lb Solution s -P_ 2-8 AE 100 lb 200 in. 0.01 in.2 1.0 x 107 lb in.2 s 0.2 in. Rev. 0 Page 13 MS-02 YOUNG S MODULUS DOE-HDBK-1017 1-93 Properties of Metals Summary The important information in this chapter is summarized below. Young s Modulus Summary Hooke s Law states that in the elastic range of a material strain is proportional to stress. It is measured by using the following equation 8 AE Young s Modulus Elastic Modulus is the ratio of stress to strain or the gradient of the stress-strain graph. It is measured using the following equation E e MS-02 Page 14 Rev. 0 Properties of Metals DOE-HDBK-1017 1-93 STRESS-STRAIN RELATIONSHIP STRESS-STRAIN RELATIONSHIP Most polycrystalline materials have within their elastic range an almost constant relationship between stress and strain. Experiments by an English scientist named Robert Hooke led to the formation of Hooke s Law which states that in the elastic range of a material strain is .
TÀI LIỆU LIÊN QUAN
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 2
Material Science_ Vol 2 of 2 - US DOE (1993) WW part 1
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 1
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 3
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 4
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 5
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 6
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 7
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 8
Material Science_ Vol 1 of 2 - US DOE (1993) WW Part 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.