Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 6
Đang chuẩn bị liên kết để tải về tài liệu:
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 6
Diệp Vy
50
7
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'steel heat treatment - metallurgy and technologies 2nd ed - g. totten (crc_ 2007) 6', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | When comparing the curves for the start of transformation in CCT and IT diagrams for the same heat and steel grade Figure 6.7 and Figure 6.10 we found that in the CCT diagram the curves are slightly shifted to longer times and lower temperatures. For example in the IT diagram of Figure 6.7 the shortest time to start the transformation of ferrite is 16 s at 650 C 1200 F and the corresponding time for bainite is 9 s at 480 C 900 F . In the CCT diagram of Figure 6.10 however the shortest transformation start time for ferrite is 32 s at 620 C 1150 F and the corresponding time for bainite is 20 s at 380 C 716 F . This indicates that in CCT processes the transformation starts later than in IT processes. The basis of this phenomenon is related to the incubation time and can be found in a hypothesis of Scheil 6 . It should also be noted that with higher austenitizing temperature the curves denoting the start of transformation of a particular phase can be shifted to longer times. Figure 6.11 shows the CCT diagram of DIN 16MnCr5 steel after austenitizing at 870 C 1600 F a and after austenitizing at 1050 C 1922 F b . In the latter case the regions of ferrite and pearlite are shifted to longer times. It is necessary therefore when using a CCT diagram to ascertain that the austenitizing temperature used to develop the CCT diagram corresponds to the austenitizing temperature of the parts treated. A CCT diagram is developed in the following way. Many small specimens e.g. 4-mm diameter X 2 mm for high cooling rates and 4.5-mm diameter X 15 mm for medium and low cooling rates are austenitized and cooled within a dilatometer with different cooling rates. Start and finish of transformation of relevant phases with each cooling curve are recorded and these points are connected to obtain the regions of transformation for the relevant phases see Figure 6.10 . Therefore a CCT diagram can be read only in the way in which it was developed i.e. along the cooling curves. As can be seen from .
TÀI LIỆU LIÊN QUAN
steel heat treatment metallurgy and technologies 2nd ed g totten crc 2007 ww
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 1
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 2
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 3
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 4
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 5
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 6
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 7
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 8
Steel Heat Treatment - Metallurgy and Technologies 2nd ed - G. Totten (CRC_ 2007) 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.