Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Introduction to Elasticity Part 3
Đang chuẩn bị liên kết để tải về tài liệu:
Introduction to Elasticity Part 3
Quang Tú
72
25
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'introduction to elasticity part 3', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | TRUSSES David Roylance Department of Materials Science and Engineering Massachusetts Institute of Technology Cambridge MA 02139 June 8 2000 Introduction A truss is an assemblage of long slender structural elements that are connected at their ends. Trusses find substantial use in modern construction for instance as towers see Fig. 1 bridges scaffolding etc. In addition to their practical importance as useful structures truss elements have a dimensional simplicity that will help us extend further the concepts of mechanics introduced in the modules dealing with uniaxial response. This module will also use trusses to introduce important concepts in statics and numerical analysis that will be extended in later modules to more general problems. Figure 1 Truss tower supporting the NASA wind turbine generator at Oahu Hawaii. Example 1 Trusses are often used to stiffen structures and most people are familiar with the often very elaborate systems of cross-bracing used in bridges. The truss bracing used to stiffen the towers of suspension bridges against buckling are hard to miss but not everyone notices the vertical truss panels on most such bridges that serve to stiffen the deck against flexural and torsional deformation. Many readers will have seen the very famous movie taken on November 7 1940 by Barney Elliott of The Camera Shop in Tacoma Washington. The wind was gusting up to 42 mph that day and induced a 1 sequence of spectacular undulations and eventual collapse of the Tacoma Narrows bridge1. This bridge was built using relatively short I-beams for deck stiffening rather than truss panels reportedly for aesthetic reasons bridge designs of the period favored increasingly slender and graceful-appearing structures. Even during construction the bridge became well known for its alarming tendency to sway in the wind earning it the local nickname Galloping Gertie. Truss stiffeners were used when the bridge was rebuilt in 1950 and the new bridge was free of the oscillations .
TÀI LIỆU LIÊN QUAN
Ebook Introduction to the mechanics of a continuous medium: Part 2
Ebook An introduction to continuum mechanics (2nd edition): Part 2
Ebook Economics - A contemporary introduction (9th edition): Part 1
Introduction to Elasticity Part 1
Introduction to Elasticity Part 2
Introduction to Elasticity Part 3
Introduction to Elasticity Part 4
Introduction to Elasticity Part 5
Introduction to Elasticity Part 6
Introduction to Elasticity Part 7
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.