Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
IADC Drilling Manual Part 7
Đang chuẩn bị liên kết để tải về tài liệu:
IADC Drilling Manual Part 7
Ánh Dương
60
74
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'iadc drilling manual part 7', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Chapter J Pumps Figure J4-37 Protection of Studs while using Wedge-type Pullers Figure J4-37. When wedge-type pullers are used on pumps with stud-type valve pet covers a rag inserted in the crotch of the wedge will protect the studs. International Association of Drilling Contractors J-67 IADC Drilling Manual - Eleventh Edition Figure J4-38 Pulling the Valve Seat Figure J4-38. The valve seat is then pulled by striking the wedge with a sledge hammer. J-68 International Association of Drilling Contractors Chapter J Pumps Figure J4-39 Valve Seat Puller Assembly Figure J4-39. This photograph shows the entire valve seat puller assembly immediately after it has been removed from the valve pot. Hydraulic jack pullers employ the same type puller head as the wedge type only the stem is longer for the jack. Place the jack over the stem on the two piece block and install the nut. Insert the C washer between the top of the jack and the nut. Release the fluid return valve to compress puller . and bring the nut up as tight as possible. To prevent injury when the seat releases and pulls out of the deck secure a safety chain around the pulling assembly Figure J4-35. On duplex and single acting L head pumps all the valves are accessible from the top and may be changed easily. However on single acting cylinder head pumps the intake valve is directly below the discharge valve and requires a special pulling tool Figure J4-40. International Association of Drilling Contractors .
TÀI LIỆU LIÊN QUAN
IADC Drilling Manual Part 1
IADC Drilling Manual Part 2
IADC Drilling Manual Part 3
IADC Drilling Manual Part 4
IADC Drilling Manual Part 5
IADC Drilling Manual Part 6
IADC Drilling Manual Part 7
IADC Drilling Manual Part 8
IADC Drilling Manual Part 9
IADC Drilling Manual Part 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.