Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Harris' Shock and Vibration Handbook Part 8
Đang chuẩn bị liên kết để tải về tài liệu:
Harris' Shock and Vibration Handbook Part 8
Quang Dũng
42
82
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'harris' shock and vibration handbook part 8', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | CALIBRATION OF PICKUPS 18.9 in order to reduce the effect of measurement noise curve fitting may be used to estimate the step value. Equation 18.7 shows how the sensitivity of the reference force transducer is related to the other parameters of the system. Sr SrfM - M 18.7 gM g where Sr acceleration sensitivity of the reference force transducer in mV ms 2 Srf force sensitivity of the reference force transducer in mV N M total mass on the force transducer in kg eg output of the force transducer in mV g acceleration of free fall due to gravity in ms 2 Note that eg is numerically equal to Sr expressed in mV g. Step 2. Measure the voltage ratio et er. Remove the reference force transducer reference mass and the pickup being calibrated from the drop-test fixture then mount them on the vibration exciter as shown in Fig. 18.6. By measuring the transfer function et er i.e. the ratio of the voltage output of the signal conditioner from the test pickup to the voltage output of the signal conditioner from the reference force transducer shown in Fig. 18.6 the frequency response of the test pickup can be FIGURE 18.6 System configuration for frequency response calibration by measuring acceleration-to-force ratio. measured over 0.1 to 100 000 Hz depending upon frequency range of the vibration exciter and signal-to-noise ratio of the system. For use at low frequencies the discharge time constant of the reference force transducer should be ten times greater than that of the test pickup. Step 3. Calculate the sensitivity St of the test pickup. If the reference force transducer and the test pickup are linear the acceleration sensitivity of the test pickup St expressed in the same units as Sr can be calculated from Eq. 18.1. If either velocity or displacement sensitivity of the test pickup is required it can be obtained by dividing the acceleration sensitivity by 2 f or 2 f 2 respectively. CENTRIFUGE CALIBRATOR A centrifuge provides a convenient means of applying constant acceleration
TÀI LIỆU LIÊN QUAN
HARRIS’ SHOCK AND VIBRATION HANDBOOK
Harris' Shock and Vibration Handbook Part 1
Harris' Shock and Vibration Handbook Part 2
Harris' Shock and Vibration Handbook Part 3
Harris' Shock and Vibration Handbook Part 4
Harris' Shock and Vibration Handbook Part 5
Harris' Shock and Vibration Handbook Part 6
Harris' Shock and Vibration Handbook Part 7
Harris' Shock and Vibration Handbook Part 8
Harris' Shock and Vibration Handbook Part 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.