Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Harris' Shock and Vibration Handbook Part 7
Đang chuẩn bị liên kết để tải về tài liệu:
Harris' Shock and Vibration Handbook Part 7
Bích Liên
62
82
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'harris' shock and vibration handbook part 7', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 14.32 CHAPTER FOURTEEN C FIGURE 14.28 Use of a fixed low-pass filter to prevent aliasing when tracking with an FFT analyzer employing zoom to analyze in a lower-frequency band. For illustration purposes the sampling frequency at maximum shaft speed has been made four times greater than that appropriate to the analog LP filter. The shaft speed range could be made proportionally greater by increasing this factor. A Situation at maximum shaft speed. All harmonics of interest must be contained in the display range. B Situation at one-fourth maximum shaft speed. The analog filter characteristics overlap but are well separated from the display range. C Situation at three-sixteenths maximum shaft speed. The aliasing range almost intrudes on the display range. located in line no. 240 the fundamental must be in line no. 8 there must be eight periods of the fundamental component along the data record. Where the data record contains 1024 samples i.e. N 1024 the sampling frequency must then be 128 times the shaft speed thus a frequency multiplier with a multiplication factor of 128 should be used in this specific case. For FFT analyzers with zoom a simpler approach can be used as illustrated in Fig. 14.28. An analog low-pass filter is applied to the signal with a cutoff frequency corresponding to the highest required harmonic at maximum shaft speed. However a frequency multiplying factor is chosen so as to make the sampling frequency say 10 or 20 times this cutoff frequency instead of the normal 2.56 . The spectrum then VIBRATION ANALYZERS AND THEIR USE 14.33 is obtained by zooming in a range corresponding to the highest required harmonic. As shown in Fig. 14.28 the shaft speed and thus the sampling frequency can then be varied over a wide range without aliasing components affecting the measurement results. A somewhat similar procedure is used in conjunction with the digital resampling technique mentioned above. By using four times oversampling a maximum speed range of 5.92 1
TÀI LIỆU LIÊN QUAN
HARRIS’ SHOCK AND VIBRATION HANDBOOK
Harris' Shock and Vibration Handbook Part 1
Harris' Shock and Vibration Handbook Part 2
Harris' Shock and Vibration Handbook Part 3
Harris' Shock and Vibration Handbook Part 4
Harris' Shock and Vibration Handbook Part 5
Harris' Shock and Vibration Handbook Part 6
Harris' Shock and Vibration Handbook Part 7
Harris' Shock and Vibration Handbook Part 8
Harris' Shock and Vibration Handbook Part 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.