Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Friction, Lubrication, and Wear Technology (1997) Part 8
Đang chuẩn bị liên kết để tải về tài liệu:
Friction, Lubrication, and Wear Technology (1997) Part 8
Công Phụng
86
130
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'friction, lubrication, and wear technology (1997) part 8', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | L L62L 2it 1.10 exp I- Eq 26 Isotropic elasticity theory has been used to obtain these relationships for dislocation density and correlation parameters. In applying Eq 24 one need not assume that the material is isotropic. Table 1 lists results for both face- and body-centered cubic materials. A common pattern is apparent. For cold-work fdings one finds that i.33 - 2.17 Eq 27 For the most part the dislocation density is high and in the lO Vcm2 range. Dislocations are highly correlated with Rc close to the average diameter of the subgrain for metallic filings and ZrO2 debris. Table 1 Results for body-centered cubic materials face-centered cubic aluminum and partially stabilized cubic zirconia Material . . nm n X 10 n cm2 RJ L X 104 X 10 Cr 28.5 3.67 1.79 2.63 1.47 V 20.0 6.56 2.17 3.46 4.05 Mo 26.0 4.60 1.99 3.30 2.72 w 21.5 7.32 1.66 4.56 3.27 Nb 20.0 1.53 1.33 0.84 0.29 Al 32.0 4.41 1.64 2.32 1.60 ZrO2 8.6 12.70 1.42 4.84 4.90 Aluminum filings are prepared under liquid nitrogen. Source Ref 18 The results given in Table 1 for body- and face-centered cubic material allow a simple explanation to be given for the structure of cold-worked fragments. Filings show a high degree of correlation small RJ L and high dislocation densities. This is related to sample conditions such as the temperature and local conditions at which a high-density dislocation structure is produced. Fragments produced by filing or grinding at room temperature or even at liquid nitrogen temperature cannot be cold. Instead they are rapidly heated to a high temperature during fracture and rapidly quenched because of their high surface-to-volume ratio. Dislocations are mobile for short periods of time over short distances and can cluster. Table 1 includes results from cubic debris particles obtained from a worn PSZ. The substrate contains three phases as already discussed. It should be noted that the cubic phase is stable at high temperatures making it reasonable that only the cubic form should be .
TÀI LIỆU LIÊN QUAN
Friction, Lubrication, and Wear Technology (1997) Part 1
Friction, Lubrication, and Wear Technology (1997) Part 2
Friction, Lubrication, and Wear Technology (1997) Part 3
Friction, Lubrication, and Wear Technology (1997) Part 4
Friction, Lubrication, and Wear Technology (1997) Part 5
Friction, Lubrication, and Wear Technology (1997) Part 6
Friction, Lubrication, and Wear Technology (1997) Part 7
Friction, Lubrication, and Wear Technology (1997) Part 8
Friction, Lubrication, and Wear Technology (1997) Part 9
Friction, Lubrication, and Wear Technology (1997) Part 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.