Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Công Nghệ Thông Tin
Quản trị mạng
Cisco Network part 89
Đang chuẩn bị liên kết để tải về tài liệu:
Cisco Network part 89
Ánh Trang
75
5
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'cisco network part 89', công nghệ thông tin, quản trị mạng phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | int fa0 0 ip addr blah ip nat outside int fa0 1 ip addr blah ip nat outside ip nat poop ISP1 ISP1_Valid_range_here prefix-length blah ip nat pool Cable Cable_Valid_range_here prefix-length blah These uses below are allowed to use the NAT service. access-list 1 permit 10.0.0.0 0.255.255.255 route-map ISP1 perm 10 match ip addr 1 match interface fa0 0 route-map Cable perm 10 match ip addr 1 match interfa fa0 1 From Question 64 Subject Sample config of using VIC BRI interfaces as an ISDN switch. Enter this under stupid router tricks it s got to be more expensive than an ISDN emulator but not if you ve got the parts lying around . Switch Cisco 2600 or 3600 with NM-2V and VIC-2BRI-S T-TE NT should work too IOS 12.1.5T9 R1 R2 Cisco with ISDN BRI S T interface. IOS 12.x R1 S T crossover cable Switch S T crossover R2 These configs let you do ISDN BRI dialup between two routers using a third router as an ISDN switch. Call setup is flakey but otherwise it seems to work once the call is up. Switch config for ISDN dial and X.25 over ISDN D-channel thrown in too isdn switch-type basic-net3 x25 routing interface Loopback0 ip address 10.0.0.1 255.255.255.255 whatever interface BRI1 0 description to R1 no ip address isdn switch-type basic-net3 isdn overlap-receiving isdn protocol-emulate network isdn layer1-emulate network isdn incoming-voice voice isdn x25 dchannel isdn skipsend-idverify Basic X.25 over D channel so you can run pad commands For always on see the Cisco docs interface BRI1 0 0 no ip address ip mtu 1514 no ip mroute-cache x25 address 5552000 clns mtu 1514 interface BRI1 1 description to R2 no ip address isdn switch-type basic-net3 isdn protocol-emulate network isdn layer1-emulate network isdn incoming-voice voice isdn skipsend-idverify interface BRI1 1 0 no ip address ip mtu 1514 no ip mroute-cache x25 address 5551000 clns mtu 1514 x25 route 5551111 interface BRI1 1 0 x25 route 5552222 interface BRI1 0 0 voice-port 1 0 0 voice-port 1 0 1 dial-peer voice 1 pots .
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.