Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Inspection of Vertical Transportation Equipment_2
Đang chuẩn bị liên kết để tải về tài liệu:
Inspection of Vertical Transportation Equipment_2
Nhật Quốc
84
27
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'inspection of vertical transportation equipment_2', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Simpo PDF Merge and Split Unregistered Version - http www.simpopdf.com Values are based on 12 -0 floor-to-floor height. Adjust using factors noted for variation from this standard. Find rated speed in the 1st column. Select standard floor-to-floor performance time from box under correct door type side opening or center opening and clear door opening width. Adjust this time by adding factor if doors are over 7 -6 high and adding or subtracting appropriate amount per foot of travel over or under standard floor height of 12-0 . NOTE All times are based on heavy duty high speed door operating equipment and optimum adjustment. On geared applications with medium speed door operators add 1.0 second. on gearless applications add 0.5 second for less stringent requirement. 2.2 INSIDE THE CAR INSPECTION 2.2.1 Scope Division 101 of the A17.2 Manual covers the inspections made from inside the car. This section of the A17.2 Manual is quite complete and covers the majority of the items to be examined. However the Inspector must also examine the inside of the car to be sure all operating equipment is functioning in its intended manner and that the appearance of the area is acceptable to the riders. This same consideration should also be exercised when examining freight elevators. 2.2.2 Operating and Signalling Devices All operating and signalling devices should be operating as intended and check to see that all fastenings are in place and secure. The signalling devices are important to the elevator operation because they are designed to project operating information for the purpose of expediting traffic movement. Examples of this information are which car is moving up or down which car is loading where the car is in the hoistway was your call registered etc. Also it should have handicapped identification for operating devices that are provided and properly displayed. 2.2.3 Car Enclosure The overall enclosure should not have loose or missing components or hardware. Handrails .
TÀI LIỆU LIÊN QUAN
Inspection of Vertical Transportation Equipment_1
Inspection of Vertical Transportation Equipment_2
Inspection of Vertical Transportation Equipment_3
Inspection of Vertical Transportation Equipment_4
Inspection of Vertical Transportation Equipment_5
Inspection of Vertical Transportation Equipment_6
Inspection of Vertical Transportation Equipment_7
Inspection of Vertical Transportation Equipment_8
Inspection of Vertical Transportation Equipment_9
Inspection of Vertical Transportation Equipment_10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.