Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Engineering Materials vol 2 Part 6
Đang chuẩn bị liên kết để tải về tài liệu:
Engineering Materials vol 2 Part 6
Hạnh Vi
66
25
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'engineering materials vol 2 part 6', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Fig. 11.3. Microstructures during the slow cooling of a eutectoid steel from the hot working temperature. Ás a point of detail when pearlite is cooled to room temperature the concentration of carbon in the a decreases slightly following the a a Fe3C boundary. The excess carbon reacts with iron at the a-Fe3C interfaces to form more Fe3C. This plates out on the surfaces of the existing Fe3C plates which become very slightly thicker. The composition of Fe3C is independent of temperature of course. Fig. 11.4. Microstructures during the slow cooling of a hypoeutectoid steel from the hot working temperature. Á3 is the standard labelling for the temperature at which a first appears and Á1 is standard for the eutectoid temperature. Hypoeutectoid means that the carbon content is below that of a eutectoid steel in the same sense that hypodermic means under the skin . Fig. 11.5. Microstructures during the slow cooling of a hypereutectoid steel. Ácm is the standard labelling for the temperature at which Fe3C first appears. Hypereutectoid means that the carbon content is above that of a eutectoid steel in the sense that a hyperactive child has an above-normal activity . Fig. 11.6. Room temperature microstructures in slowly cooled steels of different carbon contents. a The proportions by weight of the different phases. b The proportions by weight of the different structures. 118 Engineering Materials 2 to A1. At A1 the remaining Y which is now of eutectoid composition transforms to pearlite as usual. The room temperature microstructure is then made up of primary a pearlite. If the steel contains more than 0.80 C a hypereutectoid steel then we get a room-temperature microstructure of primary Fe3C plus pearlite instead Fig. 11.5 . These structural differences are summarised in Fig. 11.6. Mechanical properties of normalised carbon steels Figure 11.7 shows how the mechanical properties of normalised carbon steels change with carbon content. Both the yield strength and tensile .
TÀI LIỆU LIÊN QUAN
Engineering Materials vol 2 Part 2
Engineering Materials vol 1 Part 2
Engineering Materials vol 2 Part 15
Engineering Materials vol 2 Part 16
Engineering Materials vol 2 Part 1
Engineering Materials vol 2 Part 4
Engineering Materials vol 2 Part 3
Engineering Materials vol 2 Part 5
Engineering Materials vol 2 Part 6
Engineering Materials vol 2 Part 7
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.