Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Engineering Mechanics Statics - Examples Part 13
Đang chuẩn bị liên kết để tải về tài liệu:
Engineering Mechanics Statics - Examples Part 13
Ngọc Vy
73
70
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'engineering mechanics statics - examples part 13', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Engineering Mechanics - Statics Chapter 8 Pcb Fe 2 2 ---------------- 7 b c cos p b sin p a The equilibrium of clamped block requires that Fd Fe Fe 72.7 N Fd 72.7 N Problem 8-82 The clamp provides pressure from several directions on the edges of the board. If the square-threaded screw has a lead h radius r and the coefficient of static friction is as determine the horizontal force developed on the board at A and the vertical forces developed at B and C if a torque M is applied to the handle to tighten it further. The blocks at B and C are pin-connected to the board. Given h 3 mm r 10 mm As 0.4 M 1.5 N- m p 45 deg Solution h atan as . h A e atan ỵ 2 nrJ M Axr tan 0s e s Fx 0 Ax - 2Tcos p 0 Cy T sin p ệs 21.801 deg e 2.734 deg Ax M r tan 0s e Ax 329 N . A x 1 A T 2 Icos p J T 232.36 N By Cy B B Cy 7 164.3 164.3 N 842 2007 R. C. Hibbeler. Published by Pearson Education Inc. Upper Saddle River NJ. All rights reserved. This material is protected under all copyright laws as they currently exist. No portion of this material may be reproduced in any form or by any means without permission in writing from the publisher. Engineering Mechanics - Statics Chapter 8 Problem 8-83 The two blocks under the double wedge are brought together using a left and right square-threaded screw. If the mean diameter is d the lead is rb and the coefficient of static friction is Fs determine the torque needed to draw the blocks together. The coefficient of static friction between each block and its surfaces of contact is Fs. Units Used kN 103 N Given F 5 kN ớ 20 deg d 20 mm ri 5 mm Fs 0.4 F s 0.4 Solution Top block -F 2N1 cos ớ - 2ạ sNì sin ớ 0 F Nì ì----T-T 7 2 cos ớ - ụ s sin ớ Nj 3.1138kN Bottom block N - Nị cos ớ ựsNi sin ớ 0 N N1 cos ớ - u s N sin ớ N 2.50 kN -N sin ớ - ựsNi cos ớ T- F sN 0 T N1 sin ớ u s N cos ớ F s N T 3.2354 kN 843 2007 R. C. Hibbeler. Published by Pearson Education Inc. Upper Saddle River NJ. All rights reserved. This material is protected under all copyright laws as .
TÀI LIỆU LIÊN QUAN
Engineering Mechanics Statics - Examples Part 1
Engineering Mechanics Statics - Examples Part 2
Engineering Mechanics Statics - Examples Part 3
Engineering Mechanics Statics - Examples Part 4
Engineering Mechanics Statics - Examples Part 5
Engineering Mechanics Statics - Examples Part 6
Engineering Mechanics Statics - Examples Part 7
Engineering Mechanics Statics - Examples Part 8
Engineering Mechanics Statics - Examples Part 9
Engineering Mechanics Statics - Examples Part 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.