Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Standard Handbook of Engineering Calculations Episode 1
Đang chuẩn bị liên kết để tải về tài liệu:
Standard Handbook of Engineering Calculations Episode 1
Hồng Thúy
81
110
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'standard handbook of engineering calculations episode 1', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | McGraw-Hill STANDARD HANDBOOKS Standard Handbook of Engineering Calculations I o ư R T II E D IT I o N ---w r Y L E R G . HICKS Source STANDARD HANDBOOK OF ENGINEERING CALCULATIONS SECTION 1_ CIVIL ENGINEERING PART 1 STRUCTURAL STEEL DESIGN STEEL BEAMS AND PLATE GIRDERS 1.4 Most Economic Section for a Beam with a Continuous Lateral Support under a Uniform Load 1.5 Most Economic Section for a Beam with Intermittent Lateral Support under Uniform Load 1.5 Design of a Beam with Reduced Allowable Stress 1.6 Design of a Cover-Plated Beam 1.8 Design of a Continuous Beam 1.11 Shearing Stress in a Beam Exact Method 1.12 Shearing Stress in a Beam Approximate Method 1.12 Moment Capacity of a Welded Plate Girder 1.13 Analysis of a Riveted Plate Girder 1.13 Design of a Welded Plate Girder 1.15 STEEL COLUMNS AND TENSION MEMBERS 1.18 Capacity of a Built-Up Column 1.19 Capacity of a Double-Angle Star Strut 1.19 Section Selection for a Column with Two Effective Lengths 1.20 Stress in Column with Partial Restraint against Rotation 1.21 Lacing of Built-Up Column 1.22 Selection of a Column with a Load at an Intermediate Level 1.23 Design of an Axial Member for Fatigue 1.23 Investigation of a Beam Column 1.24 Application of Beam-Column Factors 1.25 Net Section of a Tension Member 1.25 Design of a Double-Angle Tension Member 1.26 PLASTIC DESIGN OF STEEL STRUCTURES 1.27 Allowable Load on Bar Supported by Rods 1.28 Determination of Section Shape Factors 1.29 Determination of Ultimate Load by the Static Method 1.30 Determining the Ultimate Load by the Mechanism Method 1.31 Analysis of a Fixed-End Beam under Concentrated Load 1.32 Analysis of a Two-Span Beam with Concentrated Loads 1.32 Selection of Sizes for a Continuous Beam 1.34 Mechanism-Method Analysis of a Rectangular Portal Frame 1.36 Analysis of a Rectangular Portal Frame by the Static Method 1.38 Theorem of Composite Mechanisms 1.39 Analysis of an Unsymmetric Rectangular Portal Frame 1.39 Analysis of Gable Frame by Static .
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.