Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Dimensioning and Tolerancing Part 7
Đang chuẩn bị liên kết để tải về tài liệu:
Dimensioning and Tolerancing Part 7
Tường Lâm
87
15
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'dimensioning and tolerancing part 7', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | ASME Y14.6M-1994 DIMENSIONING AND TOLERANCING I 5.3.5 FIG. 5-12 INCREASE IN POSITIONAL TOLERANCE WHERE HOLE IS NOT AT LMC DIMENSIONING AND TOLERANCING ASME Y14.5M-1994 THIS ON THE DRAWING MEANS THIS AT LMC FIG. 5-13 LMC APPLIED TO BOSS AND HOLE 91 ASME Y14.5M-1994 DIMENSIONING AND TOLERANCING THIS ON THE DRAWING FIG. 5-14 LMC APPUED TO PATTERN OF SLOTS 5.3.6 Multiple Patterns of Features Located by Basic Dimensions Relative to Common Datums. Where two or more patterns of features are located by basic dimensions relative to common datum features referenced in the same order of precedence and at the same material conditions the following apply. 5.3.6.1 Simultaneous Requirement RFS. Where multiple patterns of features are located relative to common datum features not subject to size tolerances or to common datum features of size specified on an RFS basis they are considered to be a single pattern. For example in Fig. 5-16 each pattern of features is located relative to common datum features not subject to size tolerances. Since all locating dimensions are basic and all measurements are .
TÀI LIỆU LIÊN QUAN
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2
Geometric Dimensioning and Tolerancing for Mechanical Design Part 3
Geometric Dimensioning and Tolerancing for Mechanical Design Part 4
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5
Geometric Dimensioning and Tolerancing for Mechanical Design Part 6
Geometric Dimensioning and Tolerancing for Mechanical Design Part 7
Geometric Dimensioning and Tolerancing for Mechanical Design Part 8
Geometric Dimensioning and Tolerancing for Mechanical Design Part 9
Geometric Dimensioning and Tolerancing for Mechanical Design Part 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.