Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Ultra Wideband Part 15
Đang chuẩn bị liên kết để tải về tài liệu:
Ultra Wideband Part 15
Tuệ Lâm
75
30
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'ultra wideband part 15', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 414 Ultra Wideband and goes on with B then continue with C. For example the prototype 4 A first fixing the taper s height LR2 to 4.335mm then B optimizing the taper width Wt and then C adjust the WC for the radiation-characteristics. The optimized results showed an SWB impedance bandwidth of at least over 150GHz. In fact the result of prototype 4 with parameters listed in column 4 of Table.1 shown the downtrend of reflection coefficient for increasing frequency Fig. 2 we expect that prototype 4 will well-behave beyond 150GHz as well. Fig. 5. Impedance bandwidth of the developed prototypes. Ordinate magnitude of the reflection coefficient dB Abscissa frequency GHz . Parameter mm Prototype 1 Prototype 2 Prototype 3 Prototype 4 Description Lf 4.25 4.25 4.25 4.25 Length of the feed section Rf 0.5 0.5 0.5 0.5 Blending radius in the feed section WGND 6.86 6.86 6.86 6.86 Width of the ground Ws 2 2 2 2 Width of the signal line Wg 0.14 0.14 0.14 0.14 Width of the CPW s gap Lt 3.64 1.64 1.64 1.64 Tapering length in the transition region Wt 10.2 10.2 9.2 A 8.5 B Upper tapering in the transition region Lri 4.33 4.33 4.33 4.33 Resonator length in the radiating region Lr2 4.335 4.335 1.835 B 4.335 A Resonator length in the matched radiating region Wr 10.5 10.5 10.5 10.5 Resonator width in the radiating region Wc 7 7 7 7.2 C Circle s separation width r 2.5 2.5 2.5 2.5 Radius of the top circle area Bandwidth 4-14GHz 5-25GHz 6.5-45GHz 5-150GHz Bandwidth enhancement Table 1. Parameters of the prototypes all dimensions are in mm the alphabetical order A B C indicates the priority-order of parameters in the SVO process. On the Design of a Super Wide Band Antenna 415 5. Design and Fabrication 5.1 Design All prototypes depicted in Fig. 4 with their design dimensions listed in table.1 have been fabricated on Duroid RT 5880 high frequency laminate with substrate height h 0.787mm copper cladding thickness t 17pm relative dielectric constant r 2.2 electric and magnetic loss tangents are .
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.