Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Corrosion of Ceramic and Composite Materials Part 2
Đang chuẩn bị liên kết để tải về tài liệu:
Corrosion of Ceramic and Composite Materials Part 2
Ðăng Ðạt
39
26
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'corrosion of ceramic and composite materials part 2', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 16 Chapter 2 layer was determined to be the rate-limiting step during dissolution. The composition of the boundary layer may vary depending upon whether diffusion is more or less rapid than the boundary reaction. The basic equation describing the rate of solution under free convection with density being the driving force is dR 0.505 vix 1 4 D 3 4C exp 5 R 5 4y 2.3 where g acceleration due to gravity Ap p -p p p sarurared liquid density and p original v kinematic viscosity x distance from surface of liquid Di interface diffusion coefficient C a concentration parameter 5 effective boundary layer thickness R solute radius The exponential term was introduced as a correction for cylindrical surfaces. Since experimental tests often involve cylindrical specimens these equations have been developed for that geometry. In practical applications the condition relating to the corrosion of slabs is most predominant. However if the sample diameter is large compared to the boundary layer thickness the two geometries give almost identical results. After a short induction period which is of no consequence in practical applications in which molecular diffusion predominates the rate of corrosion becomes nearly independent of time. As a surface corrodes the interface if denser than the corroding medium will be eroded away due to free convection caused by density variation. Use of this equation implies that one has at his disposal data relating to the variation of density and viscosity with temperature. In cases where these data are not available the investigator will need to determine them prior to any calculation of corrosion rates. Copyright 2004 by Marcel Dekker Inc. Fundamentals 17 Hrma 2.13 has used the work of Cooper and Kingery to discuss further the rates of corrosion of refractories in contact with glass. The following equation given by Hrma describes the corrosion under the condition of free convection due to density difference Jc 2.4 where jc rate of corrosion c solubility
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.