Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Composites Manufacturing - Materials, Product, and Process Engineering Part 15
Đang chuẩn bị liên kết để tải về tài liệu:
Composites Manufacturing - Materials, Product, and Process Engineering Part 15
Phương Trà
22
3
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'composites manufacturing - materials, product, and process engineering part 15', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Movable cutting bed FIGURE 10.5 Schematic of waterjet cutting equipment. Adapted from Hurlburt G.H. and Cheung J.B. Waterjet Cutting of Advanced Composite Materials SME Technical Paper No. MR77-225 Society of Manufacturing Engineers 1997. used to cut the material. Water speeds of 2600 ft s 800 m s and nozzle diameters on the order of 0.010 in. 0.25 mm are typical. For most composite applications abrasive particles are added with the water to increase the cutting speed and to cut thick composite laminates. A schematic diagram of commercially available waterjet cutting equipment is shown in Figure 10.5. As shown the water nozzle remains stationary and the sample material travels by a hydraulic cylinder. A 30-gpm 113.5 l min hydraulic pump delivers hydraulic oil at up to 3000 psi 21 MPa to an intensifier via a four-way valve. The intensifier is a differential-area doubleacting piston type in which a large piston is shuttled back and forth by the 3000 psi oil. There are two small pistons attached directly to the large piston. The small pistons have an area 1 20th of the large piston thus it converts the 3000-psi oil to 60 000 psi water. Compressed water then flows out of the high-pressure cylinders to the nozzle through a pair of check valves. During waterjet cutting the process parameters that affect cutting performance include Waterjet pressure Cutting speed Laminate thickness Nozzle orifice diameter 0.2-8 mm Hurlburt and Cheung6 performed waterjet cutting on graphite epoxy glass epoxy Kevlar epoxy boron epoxy and hybrids of graphite epoxy and 2002 by CRC Press LLC Movable cutting bed FIGURE 10.5 Schematic of waterjet cutting equipment. Adapted from Hurlburt G.H. and Cheung J.B. Waterjet Cutting of Advanced Composite Materials SME Technical Paper No. MR77-225 Society of Manufacturing Engineers 1997. used to cut the material. Water speeds of 2600 ft s 800 m s and nozzle diameters on the order of 0.010 in. 0.25 mm are typical. For most composite applications abrasive .
TÀI LIỆU LIÊN QUAN
Composites Manufacturing - Materials, Product, and Process Engineering Part 1
Composites Manufacturing - Materials, Product, and Process Engineering Part 2
Composites Manufacturing - Materials, Product, and Process Engineering Part 3
Composites Manufacturing - Materials, Product, and Process Engineering Part 4
Composites Manufacturing - Materials, Product, and Process Engineering Part 5
Composites Manufacturing - Materials, Product, and Process Engineering Part 6
Composites Manufacturing - Materials, Product, and Process Engineering Part 7
Composites Manufacturing - Materials, Product, and Process Engineering Part 8
Composites Manufacturing - Materials, Product, and Process Engineering Part 9
Composites Manufacturing - Materials, Product, and Process Engineering Part 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.