Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Công Nghệ Thông Tin
Đồ họa - Thiết kế - Flash
AutoCAD Basics 2004 bible phần 3
Đang chuẩn bị liên kết để tải về tài liệu:
AutoCAD Basics 2004 bible phần 3
Diệu Hồng
85
132
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Nếu bạn đang sử dụng kỹ thuật, đơn vị kiến trúc, AutoCAD sẽ hiển thị inch một phần khác nhau hơn so với các định dạng, bạn phải sử dụng để loại chúng. Bạn phải nhập tọa độ mà không có bất kỳ không gian bởi vì AutoCAD giải thích một không gian như tương đương với cách nhấn phím Enter và kết thúc đầu vào của bạn. | 222 Part II Drawing in Two Dimensions Before trimming After trimming Figure 10-15 Trimming two arcs to an implied intersection _ To trim an object choose Trim from the Modify toolbar. You cannot select objects before starting the TRIM command. AutoCAD displays the Current settings Projection UCS Edge None Select cutting edges . Select objects prompt. AutoCAD lets you know the values of the two system variables that affect trimming. The Projection setting is used only for 3D models. The Edge setting is used for implied intersections. When Edge is set to Extend AutoCAD trims to the implied intersection of the cutting edge and the object to be trimmed. At this prompt pick the object s that you want to use as a cutting edge. Press Enter to end object selection. Tip If the object you want to use for the cutting edge is already selected before you start the TRIM command AutoCAD deselects it. At the Sel ect cutting z edges . prompt you can type p J to reselect that object. You can trim to an actual or an implied intersection an intersection that would exist if objects were extended If you want to trim to an actual intersection at the Select object to trim or shift-select to extend or Project Edge Undo prompt select objects to trim. Be sure to pick each object between the cutting edge and the end you want to trim off. Press Enter to end object selection. AutoCAD trims the object s . If you want to trim to an implied intersection at the Select object to trim or shift-select to extend or Project Edge Undo prompt type e J. AutoCAD responds with the Enter an implied edge extension mode Extend No extend No extend prompt. Type e J. Then select the objects that you want to trim at the Select object to trim or shift-select to extend or Project Edge Undo prompt. Be sure to pick each object at or near the end that you want to trim. Press Enter to end object selection. AutoCAD trims the object s . Chapter 10 Editing Your Drawing Advanced Tools 223 Use the Undo option if the results .
TÀI LIỆU LIÊN QUAN
AutoCAD Basics 2004 bible phần 2
AutoCAD Basics 2004 bible phần 3
AutoCAD Basics 2004 bible phần 4
AutoCAD Basics 2004 bible phần 5
AutoCAD Basics 2004 bible phần 6
AutoCAD Basics 2004 bible phần 7
AutoCAD Basics 2004 bible phần 8
AutoCAD Basics 2004 bible phần 9
AutoCAD Basics 2004 bible phần 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.