Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Rotating Machinery Vibration 2011 Part 11
Đang chuẩn bị liên kết để tải về tài liệu:
Rotating Machinery Vibration 2011 Part 11
Thái Hà
31
25
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'rotating machinery vibration 2011 part 11', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 232 Chapter 7 With the magnet essentially stationary in the transducer s frequency range of use typically 10 to 1 500 Hz vibration of the electrical coil rigidly attached to the housing causes the magnetic flux lines to induce a voltage in the coil proportional to velocity of housing vibration. Thus a velocity transducer produces a selfgenerated low-impedance velocity-proportional electrical signal which can be fed to monitoring and data acquisition systems without additional signal conditioning. Velocity transducers are therefore popular in many rotating machinery applications. However because a velocity transducer has internal moving parts its use is less popular in hostile environments where relatively higher ruggedness is demanded as more inherent with an accelerometer. 2.3. Displacement Transducers 2.3.1. Background The internals of many types of rotating machinery especially turbomachinery have a number of quite small annular radial clearance gaps between the rotor and the stator e.g. journal bearings annular seals balance drums and blade-tip clearances. Therefore one obvious potential consequence of excessive rotor vibration is rotor-stator rubbing contact or worse impacting. Both accelerometers and velocity transducers measure vibration of nonrotating parts of a machine and thus cannot provide any direct information on rotor motion relative to the stator. The importance of rotor motion relative to stator motion led to the development of transducers to provide continuous instantaneous rotor-to-stator position measurements typically at each journal bearing. The earliest rotor-stator position measurement device widely applied is commonly referred to as a shaft rider and it is kinematically similar to a typical spring-loaded IC engine valve tracking its cam profile. That is a shaft rider is essentially a radial stick that is spring loaded against the journal to track the journal radial motion relative to a fixed point on the nonrotating part of the machine e.g.
TÀI LIỆU LIÊN QUAN
Rotating Machinery Vibration 2011 Part 1
Rotating Machinery Vibration 2011 Part 2
Rotating Machinery Vibration 2011 Part 3
Rotating Machinery Vibration 2011 Part 4
Rotating Machinery Vibration 2011 Part 5
Rotating Machinery Vibration 2011 Part 6
Rotating Machinery Vibration 2011 Part 7
Rotating Machinery Vibration 2011 Part 8
Rotating Machinery Vibration 2011 Part 9
Rotating Machinery Vibration 2011 Part 10
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.