Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
3D Fibre Reinforced Polymer Composites Episode 2
Đang chuẩn bị liên kết để tải về tài liệu:
3D Fibre Reinforced Polymer Composites Episode 2
Lam Phương
35
20
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu '3d fibre reinforced polymer composites episode 2', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 6 3D Fibre Reinforced Polymer Composites 1.2 INTRODUCTION TO 3D FRP COMPOSITES Since the late-1960s various types of composite materials with three-dimensional 3D fibre structures incorporating z-direction fibres have been developed to overcome the shortcomings of 2D laminates. That is the development of 3D composites has been driven by the needs to reduce fabrication cost increase through-thickness mechanical properties and improve impact damage tolerance. The development of 3D composites has been undertaken largely by the aerospace industry due to increasing demands on FRP materials in load-bearing structures to aircraft helicopters and space-craft. The marine construction and automotive industries have supported the developments. 3D composites are made using the textile processing techniques of weaving knitting braiding and stitching. 3D composites are also made using a novel process known as z-pinning. Braiding was the first textile process used to manufacture 3D fibre preforms for composite. Braiding was used in the late 1960s to produce 3D carbon-carbon composites to replace high temperature metallic alloys in rocket motor components in order to reduce the weight by 30-50 Stover et al. 1971 . An example of a modern rocket nozzle fabricated by 3D braiding is shown in Figure 1.4. At the time only a few motor components were made although it did demonstrate the capability of the braiding process to produce intricately shaped components from advanced 3D composites. Shortly afterwards weaving was used for the first time to produce 3D carbon-carbon composites for brake components to jet aircraft Mullen and Roy 1972 . 3D woven composites were made to replace high-temperature metal alloys in aircraft brakes to improve durability and reduce heat distortion. Figure 1.4 3D braided preform for a rocket nozzle Courtesy of the Atlantic Research Corporation Introduction 7 It is worth noting that these early 3D composites were made of carbon-carbon materials and not fibre .
TÀI LIỆU LIÊN QUAN
A 3-dimensional fibre scaffold as an investigative tool for studying the morphogenesis of isolated plant cells
3D Fibre Reinforced Polymer CompositesL. Tong, A.P. Mouritz and M.K. BannisterElsevier...3D
3D Fibre Reinforced Polymer Composites Episode 1
3D Fibre Reinforced Polymer Composites Episode 2
3D Fibre Reinforced Polymer Composites Episode 3
3D Fibre Reinforced Polymer Composites Episode 4
3D Fibre Reinforced Polymer Composites Episode 5
3D Fibre Reinforced Polymer Composites Episode 6
3D Fibre Reinforced Polymer Composites Episode 7
3D Fibre Reinforced Polymer Composites Episode 8
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.