Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Điện - Điện tử
Electric Circuits, 9th Edition P63
Đang chuẩn bị liên kết để tải về tài liệu:
Electric Circuits, 9th Edition P63
Hiệp Hòa
51
10
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Electric Circuits, 9th Edition P63. Designed for use in a one or two-semester Introductory Circuit Analysis or Circuit Theory Course taught in Electrical or Computer Engineering Departments. Electric Circuits 9/e is the most widely used introductory circuits textbook of the past 25 years. As this book has evolved over the years to meet the changing learning styles of students, importantly, the underlying teaching approaches and philosophies remain unchanged. | 596 Active Filter Circuits 15.7 a Using only three components from Appendix H design a low-pass filter with a cutoff frequency and passband gain as close as possible to the specifications in Problem 15.6 a . Draw the circuit diagram and label all component values. b Calculate the percent error in this new filter s cutoff frequency and passband gain when compared to the values specified in Problem 15.6 a . 15.8 Design an op amp-based high-pass filter with a cutoff frequency of 4 kHz and a passband gain of 8 using a 250 nF capacitor. a Draw your circuit labeling the component values and the output voltage. b If the value of the feedback resistor in the filter is changed but the value of the resistor in the forward path is unchanged what characteristic of the filter is changed 15.9 The input to the high-pass filter designed in Problem 15.8 is 250 cos mV. a Suppose the power supplies are Vrt. What is the smallest value of Vcc that will still cause the op amp to operate in its linear region b Find the output voltage when oc. c Find the output voltage when w 0.2w . d Find the output voltage when w 5io0. 15.10 a Use the circuit in Fig. 15.4 to design a high-pass design filter with a cutoff frequency of 8 kHz and a passband gain of 14 dB. Use a 3.9 nF capacitor in the design. b Draw the circuit diagram of the filter and label all the components. 15.11 Using only three components from Appendix H design a high-pass filter with a cutoff frequency and passband gain as close as possible to the specifications in Problem 15.10. a Draw the circuit diagram and label all component values. b Calculate the percent error in this new filter s cutoff frequency and passband gain when compared to the values specified in Problem 15.10 a . Section 15.2 15.12 The voltage transfer function for either high-pass prototype filter shown in Fig. P15.12 is Figure P15.12 15.13 The voltage transfer function of either low-pass prototype filter shown in Fig. P15.13 is W t- 7 5 1 Show that if either .
TÀI LIỆU LIÊN QUAN
Electric Circuits, 9th Edition P61
Electric Circuits, 9th Edition P62
Electric Circuits, 9th Edition P63
Electric Circuits, 9th Edition P64
Electric Circuits, 9th Edition P65
Electric Circuits, 9th Edition P66
Electric Circuits, 9th Edition P67
Electric Circuits, 9th Edition P68
Electric Circuits, 9th Edition P69
Electric Circuits, 9th Edition P70
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.