Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Công Nghệ Thông Tin
Quản trị mạng
Lab 6.2.8 Password Recovery Procedure on Catalyst 2900 Series Switches
Đang chuẩn bị liên kết để tải về tài liệu:
Lab 6.2.8 Password Recovery Procedure on Catalyst 2900 Series Switches
Diệu Huyền
37
7
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Cable a network similar to the one in the diagram. The configuration output used in this lab is produced from a 2950 series switch. Any other switch used may produce different output. The following steps are to be executed on each switch unless specifically instructed otherwise. . Instructions are also provided for the 1900 Series switch, which initially displays a User Interface Menu. Select the “Command Line” option from the menu to perform the steps for this lab. Start a HyperTerminal session. Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all switches. | Cisco Systems I Lab 6.2.8 Password Recovery Procedure on a Catalyst 2900 Series Switches Switch Designation Switch Name Enable Secret Password Enable VTY and Console Passwords VLAN 1 IP Address Default Gateway IP Address Subnet Mask Switch 1 AL Switch class cisco 192.168.1.2 192.168.1.1 255.255.255.0 Straight-through cable Serial cable Console Rollover Crossover cable Objective Create and verify a basic switch configuration verify it. Change passwords to the password recovery procedure be performed. Background Preparation Cable a network similar to the one in the diagram. The configuration output used in this lab is produced from a 2950 series switch. Any other switch used may produce different output. The following steps are to be executed on each switch unless specifically instructed otherwise. . Instructions are also provided for the 1900 Series switch which initially displays a User Interface Menu. Select the Command Line option from the menu to perform the steps for this lab. Start a HyperTerminal session. Note Go to the erase and reload instructions at the end of this lab. Perform those steps on all switches in this lab assignment before continuing. Step 1 Configure the switch Configure the hostname access and command mode passwords as well as the management LAN settings. These values are shown in the chart. If problems occur while performing this configuration refer to the Basic Switch Configuration lab. Step 2 Configure the host attached to the switch Configure the host to use the same subnet for the address mask and default gateway as on the switch. 1 - 7 CCNA 3 Switching Basics and Intermediate Routing v 3.0 - Lab 6.2.8 Copyright 2003 Cisco Systems Inc. Step 3 Verify connectivity a. To verify that the host and switch are correctly configured ping the switch IP address from the host. b. Was the ping successful __ c. If the answer is no troubleshoot the host and switch configurations. Step 4 Reset the
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.