Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Công Nghệ Thông Tin
Quản trị mạng
Lab 4.2.6 Troubleshooting IP Address Issues
Đang chuẩn bị liên kết để tải về tài liệu:
Lab 4.2.6 Troubleshooting IP Address Issues
Hạo Nhiên
53
4
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Cable a network similar to the one in the previous diagram. Any router that meets the interface requirements may be used. Possible routers include 800, 1600, 1700, 2500 and 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series routers. Any other router used may produce slightly different output. The following steps are intended to be executed on each router unless specifically instructed otherwise | Cisco SrsTEMS Lab 4.2.6 Troubleshooting IP Address Issues Router 1 Router 2 Straight-through Serial cable Rollover console Crossover cable Router designation Router name Enable secret password Enable VTY and Console passwords Routing protocol RIP network statements Router 1 GAD class cisco RIP 192.168.14.0 192.168.15.0 Router 2 BHM class cisco RIP 192.168.15.0 192.168.16.0 Router designation IP host name FastEthernet 0 address Interface type Serial 0 Serial 0 address Interface type Serial 1 Serial 1 address Subnet mask all addresses Router 1 GAD 192.168.14.1 DCE 192.168.15.1 NA No address 255.255.255.0 Router 2 BHM 192.168.16.1 DTE 192.168.15.2 NA No address 255.255.255.0 Objective Configure two routers and two workstations in a small WAN. Troubleshoot problems introduced by incorrect configurations. Background Preparation Cable a network similar to the one in the previous diagram. Any router that meets the interface requirements may be used. Possible routers include 800 1600 1700 2500 and 2600 routers or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series routers. Any other router used may produce slightly different output. The following steps are intended to be executed on each router unless specifically instructed otherwise. Start a HyperTerminal session as performed in the Establishing a HyperTerminal session lab. Note Work in teams of two. Team member 1 should configure the GAD router according to the table above and its attached workstation according to the instructions below. Team member 2 1 - 4 CCNA 2 Routers and Routing Basics v 3.0 - Lab 4.2.6 Copyright 2003 Cisco Systems Inc. should configure the BHM router and its workstation. Both configurations have errors and will result in IP related communications problems. Team member 1 will then troubleshoot problems with the BHM router and .
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.