Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Tự động hoá
Microprocessor Interfacing Techniques Lab VIEW Tutorial Part 7
Đang chuẩn bị liên kết để tải về tài liệu:
Microprocessor Interfacing Techniques Lab VIEW Tutorial Part 7
Hồng Khanh
92
2
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Microprocessor Interfacing Techniques Lab VIEW Tutorial Part 7 | PHY 406 - Microprocessor Interfacing Techniques PHY 406 - Microprocessor Interfacing Techniques LabVIEW Tutorial - Part VII Wrapping It Up - SubVIs Hiding the Hard Work Encapsulation or the enclosing of a body of work into a sub-VI is an important part of serious LabVIEW programming. We are going to encapsulate this VI. To do this we will need to create an ICON and also to define the inputs and outputs required for this VI. When we encapsulate a VI the controls are replaced by the inputs to the sub-VI and the indicators are replaced by the outputs from the VI. It isn t necessary to have all the controls and indicators accessible from outside the sub-VI but in the case of controls you had probably have a good idea about what values they default to and whether these are the right values. It is probably better to use constants to prevent changes being made accidentally. Go to the front panel and pop-up on the icon in the top right. Select Edit Icon. A little graphical editor should pop-up. I am assuming that you can run somehting like this. I used the select dotted box to clear the icon and then the text tool to write and got this When you exit the icon editor you will notice that the icon has changed to your new one. This is the icon which will show when you use this entire VI as a sub-VI. Now pop-up on the icon again and select Show Connector. LabVIEW assigns a connector pattern to this VI. The general rule in LabVIEW is that inputs are on the left outputs are on the right. This connector pattern has only two slots on the right and I want three so I can change it with the pop-up Patterns and get one with three slots on the left and three on the right. Notice also that the tool has changed ot the wiring tool. To associcate each of the inputs and outputs with a particular sector of the connector pane click on the front panel item and then on the connector sector. When a connection is established the sector turns dark. Now would be a really good time to add .
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.