Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Công Nghệ Thông Tin
Kỹ thuật lập trình
HVAC Systems Design Handbook part 18
Đang chuẩn bị liên kết để tải về tài liệu:
HVAC Systems Design Handbook part 18
Hải Uyên
75
10
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
This chapter presents a basic overview of heat transfer fundamentals, particularly as they apply to HVAC. For a detailed, rigorous treatment, the reader should refer to a good college-level text on heat transfer or to the ASHRAE Handbook. | Source HVAC Systems Design Handbook Chapter 18 Engineering Fundamentals Part 3 Heat Transfer 18.1 Introduction This chapter presents a basic overview of heat transfer fundamentals particularly as they apply to HVAC. For a detailed rigorous treatment the reader should refer to a good college-level text on heat transfer or to the ASHRAE Handbook.1 18.2 Heat Transfer Modes Heat is transferred between any two bodies by one or more of three modes conduction convection and radiation. Thermal conduction refers to the direct transfer of energy between particles at the atomic level. Thermal convection may include some conduction but refers primarily to energy transfer by eddy mixing and diffusion i.e. by fluids in motion. Thermal radiation describes a complex phenomenon which includes changes in energy form from internal energy at the source to electromagnetic energy for transmission then back to internal energy at the receiver. Radiation transfer requires no intervening material and in fact works best in a perfect vacuum. In accordance with the second law of thermodynamics net heat transfer occurs in the direction of decreasing temperature. In this text the Fahrenheit F scale is used or for absolute temperatures the Rankine R scale OR F 460 . 459 Downloaded from Digital Engineering Library @ McGraw-Hill www.digitalengineeringlibrary.com Copyright 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Engineering Fundamentals Part 3 460 Chapter Eighteen 18.3 Thermal Conduction For steady-state conduction in one direction through a homogeneous material the Fourier equation applies q -kA dt dx 18.1 where q heat transfer rate Btu h k thermal conductivity Btu h ft F A area normal to flow ft2 dt dx temperature gradient oF ft The minus sign shows that heat flow takes place from a higher to a lower temperature. In HVAC calculations homogeneous barriers are never encountered even when the solid barrier is homogeneous .
TÀI LIỆU LIÊN QUAN
HVAC Systems Design Handbook part 12
HVAC Systems Design Handbook part 5
HVAC Systems Design Handbook part 6
HVAC Systems Design Handbook part 3
HVAC Systems Design Handbook part 4
HVAC Systems Design Handbook part 8
HVAC Systems Design Handbook part 7
HVAC Systems Design Handbook part 13
HVAC Systems Design Handbook part 11
HVAC Systems Design Handbook part 1
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.