Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Khoa Học Tự Nhiên
Hoá học
Compressive strength and explosive characteristics of polymer-bonded explosives based on hexogen and fluoroelastomers
Đang chuẩn bị liên kết để tải về tài liệu:
Compressive strength and explosive characteristics of polymer-bonded explosives based on hexogen and fluoroelastomers
Xuân Sơn
83
8
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
This paper describes the formulation of two polymer-bonded explosives based on RDX (hexahydro-1,3,5- trinitro-1,3,5-triazine) and fluoroelastomer binders by the water-slurry coating method. The fluoroelastomers are poly(VDF-HFP) (vinylidene fluoride-hexafluoropropene copolymer) and poly(VDF-CTFE) (vinylidene fluoride-chlorotrifluoroethylene copolymer). It has been observed that the impact sensitivity and the friction sensitivity of PBX samples were significantly lower than that of the single RDX. Results also showed that two PBX formulations have high chemical stability, high energy characteristics, and equivalent to some PBX in the world. Finally, the compressive strength of these PBX compositions was found in the range of 8-12 MPa. | Compressive strength and explosive characteristics of polymer-bonded explosives based on hexogen and fluoroelastomers
TÀI LIỆU LIÊN QUAN
The effect of joint thickness and other factors on the compressive strength of brickwork
Research on manufacturing dry mixed cement mortar with high compressive strength, high flexural strength, low shrinkage and high watertightness for restoration of damaged hydraulic structures in Vietnam
Effect of the high temperatures on the microstructure and compressive strength of high strength fibre concretes
Effect of fly ash content on the compressive strengthdevelopment of concrete
Strength development in concrete with wood ash blended cement and use of soft computing models to predict strength parameters
Strength, durability, and microstructure of high-strength mortars incorporating various ground granulated blast furnace slag contents
Designation: C 109/C 109M – 99 - Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)1
Experimental investigation and empirical modelling of FDM process for compressive strength improvement
Statistical analysis of the effective factors on the 28 days compressive strength and setting time of the concrete
The initial research on the compressive strength of mortar when using bottom ash from thermal power plants to replace natural sand in construction
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.