Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Friction stir welding process: An investigation of microstructure and mechanical properties of Al Alloy AlMg4.5Mn joint
Đang chuẩn bị liên kết để tải về tài liệu:
Friction stir welding process: An investigation of microstructure and mechanical properties of Al Alloy AlMg4.5Mn joint
Ðông Nghi
62
10
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Aluminium alloy AlMg4.5Mn has got comprehensive acceptance in the manufacturing of light weight frames, marine structures which require high strength and worthy corrosion revulsion. The present investigation work focuses on friction stir welding process in which influences of operating parameters have been studied on friction stir welded butt joints. | Friction stir welding process An investigation of microstructure and mechanical properties of Al Alloy AlMg4.5Mn joint Engineering Solid Mechanics 2017 145-154 Contents lists available at GrowingScience Engineering Solid Mechanics homepage www.GrowingScience.com esm Friction stir welding process An investigation of microstructure and mechanical properties of Al Alloy AlMg4.5Mn joint Jitender Kundua and Hari Singhb a Research Scholar Department of Mechanical Engineering National Institute of Technology Kurukshetra 136119 India b Professor Department of Mechanical Engineering National Institute of Technology Kurukshetra 136119 India A R T I C L EI N F O ABSTRACT Article history Aluminium alloy AlMg4.5Mn has got comprehensive acceptance in the manufacturing of light Received 6 October 2016 weight frames marine structures which require high strength and worthy corrosion revulsion. Accepted 3 February 2017 The present investigation work focuses on friction stir welding process in which influences of Available online operating parameters have been studied on friction stir welded butt joints. The FSWed joints 6 February 2017 Keywords specimens have been produced by experimentation at three levels of tool traverse speed and FSW tool rotational speed keeping input force and tool tilt angle constant. Mechanical properties AA5083 and microstructure of welded joints have been investigated in the present study. Change in the Micro-hardness microstructure at different zones which transforms the mechanical properties of welded joints Microstructure was due to the asymmetrical flow of material and thermal cycles around the pin. The second Ductility phase beta grains are formed as the very high temperature reached due to input parameters Tensile strength combinations. Traverse speed TS and tool rotational speed TRS are taken in a range of 16- 40 mm min and 500-1400 rpm respectively. The best combination of parameters results in higher tensile strength which is well supported by .
TÀI LIỆU LIÊN QUAN
Dtudy of effect of friction stir welding parameters on impact energy of AA7075-T6
Effect of transverse speed of the tool on microstructure and mechanical properties in dissimilar butt friction stir welding of al5083–copper sheets
Microstructure and fracture behavior of friction stir lap welding of dissimilar metals
Microstructure and fracture behavior of friction stir lap welding of dissimilar AA 6060-T5/ Pure copper
Effect of welding speed on the mechanical properties of friction stir welded aluminium alloy 5083
Fatigue crack growth at the representative zones in friction stir welding of a heat treatable aluminium alloy at 200oC
Investigation of AA5083 T-lap joint fabricated by friction stir welding
Optimization of process parameters for friction Stir welding of dissimilar Aluminum alloys (AA2024 -T6 and AA6351-T6) by using Taguchi method
Effect of welding parameters on the mechanical properties of friction-stir-welded heat-treatable AA6061-t6
Investigations on friction stir welding process to optimize the multi responses using GRA method
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.