Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Khoa Học Tự Nhiên
Hoá học
Lecture Chemical process control - Chapter 13
Đang chuẩn bị liên kết để tải về tài liệu:
Lecture Chemical process control - Chapter 13
Tú Ly
97
32
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
a | Chapter 13 Overview of Control System Design General Requirements 1. Safety. It is imperative that industrial plants operate safely so as to promote the well-being of people and equipment within the plant and in the nearby communities. Thus plant safety is always the most important control objective and is the subject of Section 10.5. 2. Environmental Regulations. Industrial plants must comply with environmental regulations concerning the discharge of gases liquids and solids beyond the plant boundaries. 3. Product Specifications and Production Rate. In order to be profitable a plant must make products that meet specifications concerning product quality and production rate. 1 Chapter 13 4. Economic Plant Operation. It is an economic reality that the plant operation over long periods of time must be profitable. Thus the control objectives must be consistent with the economic objectives. 5. Stable Plant Operation. The control system should facilitate smooth stable plant operation without excessive oscillation in key process variables. Thus it is desirable to have smooth rapid set-point changes and rapid recovery from plant disturbances such as changes in feed composition. 2 Chapter 13 Steps in Control System Design After the control objectives have been formulated the control system can be designed. The design procedure consists of three main steps 1. Select controlled manipulated and measured variables. 2. Choose the control strategy multiloop control vs. multivariable control and the control structure e.g. pairing of controlled and manipulated variables . 3. Specify controller settings.
TÀI LIỆU LIÊN QUAN
Lecture Chemical process control - Chapter 1
Lecture Chemical process control - Chapter 8
Lecture Chemical process control - Chapter 2
Lecture Chemical process control - Chapter 11
Lecture Chemical process control - Chapter 3
Lecture Chemical process control - Chapter 4
Lecture Chemical process control - Chapter 5
Lecture Chemical process control - Chapter 6
Lecture Chemical process control - Chapter 7
Lecture Chemical process control - Chapter 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.