Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Khoa Học Tự Nhiên
Hoá học
Lecture Chemical process control - Chapter 11
Đang chuẩn bị liên kết để tải về tài liệu:
Lecture Chemical process control - Chapter 11
Hòa Hợp
101
46
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
a | Lecture Chemical process control - Chapter 11 Dynamic Behavior of Closed-Loop Control Systems Chapter 11 Chapter 11 Next, we develop a transfer function for each of the five elements in the feedback control loop. For the sake of simplicity, flow rate w1 is assumed to be constant, and the system is initially operating at the nominal steady rate. Process Chapter 11 In section 4.1 the approximate dynamic model of a stirredtank blending system was developed: K1 K2 X ( s) = X1 ( s ) + W2 ( s ) (111) τs + 1 τs + 1 where Vρ w1 1− x τ= , K1 = , and K2 = (112) w w w Chapter 11 The symbol denotes the internal setpoint composition expressed as an equivalent electrical current signal. is related to the actual composition set point by the composition sensortransmitter gain Km: Chapter 11 (117) CurrenttoPressure (I/P) Transducer The transducer transfer function merely consists of a steadystate gain KIP: Pt ( s ) Chapter 11 = K IP (119) P ( s) Control Valve As discussed in Section 9.2, control valves are usually designed so that the flow rate through the valve is a nearly linear function of the signal to the valve actuator. Therefore, a firstorder transfer function is an adequate model W2 ( s ) Kv = (1110) Pt ( s ) τv s + 1 Composition SensorTransmitter (Analyzer) We assume that the dynamic behavior of the composition sensor transmitter can be approximated by a firstorder transfer function, but τm is small so it can be neglected. Xm ( s) = Km Chapter 11 Controller X ( s) Suppose that an electronic proportional plus integral controller is used. P ( s) 1 = Kc 1 + (114) E ( s) τI s P ( s) where and E(s) are the Laplace transforms of the controller p ( t) output and the error signal e(t). Kc is dimensionless. Chapter 11 1. Summer 2. Comparator Chapter 11 3. Block Y(s) .
TÀI LIỆU LIÊN QUAN
Lecture Chemical process control - Chapter 1
Lecture Chemical process control - Chapter 8
Lecture Chemical process control - Chapter 2
Lecture Chemical process control - Chapter 11
Lecture Chemical process control - Chapter 3
Lecture Chemical process control - Chapter 4
Lecture Chemical process control - Chapter 5
Lecture Chemical process control - Chapter 6
Lecture Chemical process control - Chapter 7
Lecture Chemical process control - Chapter 9
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.