Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Khoa Học Tự Nhiên
Vật lý
Repair bond strength of dual-cured resin composite core buildup materials
Đang chuẩn bị liên kết để tải về tài liệu:
Repair bond strength of dual-cured resin composite core buildup materials
Phúc Hưng
71
7
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
The reparability of dual-cured resin composite core buildup materials using a light-cured one following one week or three months storage, prior to repair was evaluated. Two different dual-cured resin composites; Cosmecore DC automix and Clearfil DC automix core buildup materials and a light-cured nanofilled resin composite; Filtek Z350 XT were used. Substrate specimens were prepared (n = 12/each substrate material) and stored in artificial saliva at 37 C either for one week or three months. Afterward, all specimens were ground flat, etched using Scotchbond phosphoric acid etchant and received Single Bond Universal adhesive system according to the manufacturers’ instructions. The light-cured nanofilled resin composite (Filtek Z350 XT) was used as a repair material buildup. To determine the cohesive strength of each solid substrate material, additional specimens from each core material (n = 12) were prepared and stored for the same periods. Five sticks (0.8 ± 0.01 mm2 ) were obtained from each specimen (30 sticks/group) for microtensile bond strength (lTBS) testing. Modes of failure were also determined. Two-way ANOVA revealed a significant effect for the core materials but not for the storage periods or their interaction. After one week, dual-cured resin composite core buildup materials (Cosmecore DC and Clearfil DC) achieved significantly higher repair lTBS than the light-cured nanofilled resin composite (Filtek Z350 XT). However, Clearfil DC revealed the highest value, then Cosmecore DC and Filtek Z350 XT, following storage for 3-month. Repair strength values recovered 64–86% of the cohesive strengths of solid substrate materials. The predominant mode of failure was the mixed type. Dual-cured resin composite core buildup materials revealed acceptable repair bond strength values even after 3- month storage. | Repair bond strength of dual-cured resin composite core buildup materials
TÀI LIỆU LIÊN QUAN
Effect of surface roughness and adhesive system on repair potential of silorane-based resin composite
Repair bond strength of dual-cured resin composite core buildup materials
FIBER REINFORCED POLYMERS - THE TECHNOLOGY APPLIED FOR CONCRETE REPAIR
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.