Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Kiến trúc - Xây dựng
Test procedure for shrinkage of concrete blocks
Đang chuẩn bị liên kết để tải về tài liệu:
Test procedure for shrinkage of concrete blocks
Thảo Nghi
49
10
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
In this paper, methods of testing the drying shrinkage of concrete blocks are evaluated. Tests were done on blocks of differing strengths, suppliers and curing procedures. The shrinkage tests were carried out as recommended in ASTM C426 [1], using the whole block as specimens and with gauge discs attached to the sides. Three variations of this set-up were also tested: a face-shell prism cut from a whole block with gauge plugs attached to the sides, the same specimen with gauge discs attached to the top and bottom and whole blocks with gauge discs attached to the top and bottom. For the case of gauge discs attached to the sides, a Humboldt strain gauge was used to measure deformation. In the case of gauge discs attached to the top and bottom, a comparator was used. Deformations on control blocks left inside the laboratory, and not submitted to the saturated and dry conditions of the ASTM C426 test, were also measured for nearly 90 days. | Canadian Masonry Symposium Banff Alberta June 8 - 12 2005 TEST PROCEDURE FOR SHRINKAGE OF CONCRETE BLOCKS G. A. Parsekian1 K. C. Barbosa2 T. B. Inforsato3 D. F. Deana4 M. S. Faria5 and C. O. da Silva6 1Professor Dept of Civil Engineering Federal University of Sao Carlos gparsekian@terra.com.br 2MSc Dept of Civil Engineering Federal University of Sao Carlos klecbarbosa@terra.com.br 3Graduate Student Dept of Civil Engineering Federal University of Sao Carlos thinforsato@bol.com.br Junior Engineer Brazilian Portland Cement Association davidson@abcp.org.br 5Senior Engineer Brazilian Portland Cement Association marcio.faria@abcp.org.br laboratory Engineer Brazilian Portland Cement Association claudio@abcp.org.br ABSTRACT In this paper methods of testing the drying shrinkage of concrete blocks are evaluated. Tests were done on blocks of differing strengths suppliers and curing procedures. The shrinkage tests were carried out as recommended in ASTM C426 1 using the whole block as specimens and with gauge discs attached to the sides. Three variations of this set-up were also tested a face-shell prism cut from a whole block with gauge plugs attached to the sides the same specimen with gauge discs attached to the top and bottom and whole blocks with gauge discs attached to the top and bottom. For the case of gauge discs attached to the sides a Humboldt strain gauge was used to measure deformation. In the case of gauge discs attached to the top and bottom a comparator was used. Deformations on control blocks left inside the laboratory and not submitted to the saturated and dry conditions of the ASTM C426 test were also measured for nearly 90 days. The results of the concrete block shrinkage test were influenced very little by the different type of initial three-day cure althought different shrinkage values were observed in the control blocks for each cure type. With regard to the test procedures only small differences in results were obtained with whole blocks or face .
TÀI LIỆU LIÊN QUAN
Test procedure for shrinkage of concrete blocks
A two-phase procedure for non-normal quantitative trait genetic association study
Software Quality Assurance: Lecture 45 - Dr. Ghulam Ahmad Farrukh
Pressure Piping Alternative Test Methods Procedure Requirements
An empirical analysis of the bond market behavior and cointegration in the selected APEC’s countries
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.