Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Thermo-physical modeling of die-sinking EDM process
Đang chuẩn bị liên kết để tải về tài liệu:
Thermo-physical modeling of die-sinking EDM process
Trí Hùng
73
12
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
(BQ) This paper reports the development of a thermo-physical model for die-sinking electric discharge machining (EDM) process using finite element method (FEM). Numerical analysis of the single spark operation of EDM process has been carried out considering the two-dimensional axi-symmetric process continuum | Journal of Manufacturing Processes 12 (2010) 45–56 Contents lists available at ScienceDirect Journal of Manufacturing Processes journal homepage: www.elsevier.com/locate/manpro Technical paper Thermo-physical modeling of die-sinking EDM process S.N. Joshi, S.S. Pande ∗ Computer Aided Manufacturing Laboratory, Department of Mechanical Engineering, Indian Institute of Technology Bombay, Mumbai – 400076, India article info Article history: Received 4 November 2009 Received in revised form 27 January 2010 Accepted 13 February 2010 Available online 16 March 2010 abstract This paper reports the development of a thermo-physical model for die-sinking electric discharge machining (EDM) process using finite element method (FEM). Numerical analysis of the single spark operation of EDM process has been carried out considering the two-dimensional axi-symmetric process continuum. The analysis is based on more realistic assumptions such as Gaussian distribution of heat flux, spark radius equation based on discharge current and discharge duration, latent heat of melting, etc., to predict the shape of crater cavity and the material removal rate (MRR). Using the developed model, parametric studies were carried out to study the effect of EDM process parameters such as discharge current, discharge duration, discharge voltage and duty cycle on the process performance. Experimental studies were carried out to study the MRR and crater shapes produced during actual machining. When compared with the reported analytical models, our model was found to predict results closer to the experimental results. The thermo-physical model developed can further be used to carry out exhaustive studies on the EDM process to obtain optimal process conditions. © 2010 The Society of Manufacturing Engineers. Published by Elsevier Ltd. All rights reserved. 1. Introduction Electric discharge machining (EDM) is a widely used nontraditional machining process in the manufacture of complex shaped dies, .
TÀI LIỆU LIÊN QUAN
Influence of molten salt-(FLiNaK) thermophysical properties on a heated tube using CFD RANS turbulence modeling of an experimental testbed
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.