Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Giới thiệu
Đăng ký
Đăng nhập
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
Thông tin
Điều khoản sử dụng
Quy định bảo mật
Quy chế hoạt động
Chính sách bản quyền
Giới thiệu
Đăng ký
Đăng nhập
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Reservoir Formation Damage Episode 3 Part 7
Đang chuẩn bị liên kết để tải về tài liệu:
Reservoir Formation Damage Episode 3 Part 7
Tuấn Khải
38
25
pdf
Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ
Tải xuống
Tham khảo tài liệu 'reservoir formation damage episode 3 part 7', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | 632 Reservoir Formation Damage Models Separating the Internal and External Filtration Processes For convenience in the modeling Pang and Sharma 1994 divide the entire filtration process into two phases 1 the initial internal cake filtration and 2 the later external cake filtration. They separate these two filtration phases by a transition time after which the particle migration into porous formation becomes negligible and an external filter cake begins forming over the injection well formation face. Sharma and Pang 1997 assumed that transition from the internal to the external cake filtration occurs when the porosity Ị of the formation face decreases to a minimum critical value Ộ by particle deposition below which particle invasion into porous media is not possible. Their models apply for single phase water flow in the near wellbore region. Hence the effect of the oil-water two-phase flow during the initial water injection period is neglected because this initial period is relatively short. Transition Time Wennberg and Sharma 1997 estimate the transition time based on the expressions given by Iwasaki 1937 for particle deposition rate and the filtration coefficient respectively as d dt Xuc 19-14 and À À.o 1 bơ 19-15 where b is an empirical constant and Xo is the filtration coefficient without particle deposition. Although more sophisticated expressions are available in the literature See Chapter 8 they used Eq. 19-15 for simplicity. Thus invoking Eq. 19-15 into Eq. 19-14 yields the following expression similar to the rate equation for particle deposition in pluggable pathways given by Gruesbeck and Collins 1982 da dt X0 l b j uc 19-16 They obtain the analytic solution of Eq. 19-16 for constant flow rate and suspension particle concentration for two cases as the following Ơ Xouct b Q 19-17 Injectivity of the Waterflooding Wells 633 ơ l Z Ịexp À ohucí -1 b 0 19-18 At the transition time the porosity attains the minimum critical porosity Ộ and the maximum critical .
TÀI LIỆU LIÊN QUAN
crossorigin="anonymous">
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.